Alltec News

Ground Resistance Monitoring

Product-Release by Alltec Corporation
Tuesday April 15, 2008

Increased concerns for Operator Safety and System Efficiency require low resistance, stable, zero current grounding systems. Managing grounding systems has always been limited to periodic testing and/or waiting for a grounding related problem to occur. Periodic Testing has its own challenges of disconnecting ground connection and available real estate for executing the IEEE 81 recommended Fall of Potential Test. Successful periodic testing only tells you the state of the grounding system while being measured, a problem could occur the day after the test and you would not know until the next test.

Changes in ambient conditions directly effect soil moisture content and temperature which are important factors influencing ground resistance. This protblem is solved with the introduction of GRM-2000-RS Ground Monitor. Now you never have to worry about your grounding system again as the continuous monitoring feature coupled with remote access capability and audible alarms, will inform of any changes in the integrity of the grounding system, allowing execution of corrective action before any electrical accident occurs.

Features

  • Meter with LCD display, membrane switch keys and a split core sensor.
  • The sensor can be installed on in-place conductors without disconnection, and can accommodate up to 500sq.mm (1000mcm) conductors.
  • High and Low alarm settings with audio alert.
  • Range of 0.5 – 999 Ohms and 0 -4 amps.
  • Variable test rates (1/hr, 1/8hr or continuous)
  • Remote monitoring accomplished through RS232; Dial-up Modem or TCP/IP.
  • Remote monitoring software specially developed for GRM-2000 RS continuously looks for alarms and in addition polls every site once a day. Software tracks anomalies and can alert an operator that reports them to the customer.
  • Software saves all data for historical review.
  • UL Listed

IWCE 2008

Events by Alltec Corporation
Saturday March 15, 2008

It is said, “What happens in Vegas, stays in Vegas,” but this was not the case with contacts made at Alltec Corporation’s booth during the International Communication Expo (IWCE) in February.

Technology end-users, public safety professionals, wireless service providers, IT professionals and dealer/consultants responsible for the planning, purchasing and implementation for their organization’s technological future went away with valuable knowledge of how Alltec Corporation products and services are able to assist their specific needs. Industries such as security, utilities, transportation, construction, education, retail, healthcare and facilities management were well represented, and many attendees were interested to learn how Alltec can assist with protecting facilities, personnel, equipment, records, and assets to reduce the risk of disruption to their critical operations.
Thousands of communication sites around the world are a testament to Alltec Corporation’s dedication to providing exceptional designs, materials and installation services to our clients. Using soil resistivity reports and site plans supplied by the client or obtained from our engineering surveys, Alltec Corporation models grounding systems to meet Motorola R56 requirements for any communication installation.

By protecting valuable instrumentation with the most modern methods, our lightning protection, surge suppression and grounding implementations assure that vital wireless communication facilities remain functional in spite of severe weather activity. Our clients consistently report total satisfaction with our solutions.

The IWCE mission is to deliver educational and networking opportunities, and exhibit the latest in technology and communication solutions. IWCE is one place where all industries and communications professionals come together to share thoughts and ideas on wireless communications technologies. With over 350 exhibitors, it is North America’s largest annual wireless communications technologies show, and a great place to showcase Alltec’s capabilities.

OSHA Certification

Training by Alltec Corporation
Friday February 15, 2008

Alltec Corporation employees are proud to announce their participation in, and certification for, the HAZWOPER Level 1 and OSHA General Safety Refresher instruction.

Provided by Global Training and Environmental, this Hazardous Waste Operations Emergency Response program has been specifically designed for students required to act as first responders and meets the requirements of 29 CFR 1910.1200. Many clients mandate this certification for on-site work at their facilities.

The course covered many topics, including those listed below:

  • OSHA (HAZWOPER Awareness Level)
  • Access to Medical Records
  • Accident Investigation
  • Blood borne Pathogens
  • Compressed Gases
  • D.O.T. – Drug & Alcohol Awareness
  • Electrical Affected Person
  • Ergonomics OSHA Section
  • Fall Prevention & Protection
  • Fire Extinguisher Awareness (Portable)
  • Hazard Communications
  • Hydrogen Sulfide Awareness
  • Job Safety Analysis
  • Knife Safety (Alternative Cutting Tools)
  • Lockout / Tagout (Affected Employees)
  • Noise Exposure
  • N.O.R.M. Awareness
  • OSHA General Duty Clause
  • Personal Protective Equipment
  • Respiratory Protective Equipment
  • Slips, Trips & Falls + Overexertion Awareness
  • Toxic & Hazardous Materials in the Workplace
  • Welding, Cutting & Brazing; Hot Work Awareness

Distributor Highlight

Corporate by Alltec Corporation
Wednesday January 30, 2008

It is with great pleasure that we highlight Alltec Corporation’s distributor for the Thailand Market, ITECLES CO. LTD. (ITE). Established in 1993, ITECLES has been providing superior quality and customer service in the arena of lightning protection, surge suppression, and grounding products and services for the telecommunications and computer industries.

Christopher Bean, President of Alltec Corporation, was favorably impressed with this Thai company during a recent visit. ITE’s superior customer service, dedication to quality, and wide-ranging yet focused intent represents a fine Alltec Affiliate.

Mr. and Mrs. Korananan emphasize how their company motto affects their approach to business: “We are going towards full customer satisfaction with a superior quality and reliability of the products and services, coupled with competitive price, on time delivery and excellent services through a total quality improvement process.” ITECLES is committed to using this motto to guide them through every business and engineering activity. All Alltec Associates can admire this spirit. Such dedication has not gone without notice either; ITE’s recent office expansion is an example of this success and has moved it in a new arena of potential.

Alltec Corporation wishes ITE much continued success and honors their continuing accomplishments, integrity and enthusiasm.

India Telecom Expo 2007

Events by Alltec Corporation
Monday December 31, 2007

Alltec Protection Systems Pvt. Ltd’s December participation in the India Telecom 2007 show in New Delhi, India introduced its products and services to various telecom industries and agencies as well as many other representative manufacturers in India and other parts of the subcontinent.

Members of private, government and public enterprises interested in fulfilling the safety requirements of their establishment from the damages caused by lightning and surges viewed Alltec Protection Systems’ display of products and services. Alltec’s working models acted as a catalyst for participants to learn about specific parameters in which Alltec’s products and services could enhance their facility safety efforts.

Though the India Telecom Expo 2007 is over, the prospects developed will continue to build Alltec Protection Systems’ presence in the Indian market.

Alltec Corporation’s participation in tradeshow exhibitions, such as the India Telecom Expo, is an integral part of its endeavors to educate industry professionals about lightning and surge protection benefits.